0
In the US, the National Electrical Code (NEC) will allow you to install single phase and three phase systems in the same conduit.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Can a three phase circuit be installed in the same conduit or in different conduits?
The conductors of any three phase circuit must be run in the same conduit. If the circuit requires a neutral, it must also run with the conductors in the same conduit. (If they were to be run in more than one conduit or raceway, the circuit would not operate properly.)
Can you run 110 and 220 volt circuits in the same conduit?
Yes, 120 and 240 volts can be run in the same conduit.
Why 2 different phase wire are not supposed to pass through same conduit?
According to the wording ,2 different phase wires "can" run through the same conduit. Not only can they, but if they are part of the same circuit they must. And in cases where conductors are paralleled, meaning more than one conductor per phase as is common in commercial and industrial installations, you put one conductor of each phase and a neutral, if one exists, and a ground in each conduit. Not doing so, meaning to put all of one phase in one conduit, causes a voltage to be induced into the conduit and a tremendous amount of heat builds up. Even when using pvc or other non-metallic conduit, somewhere along the way you have something metallic and have the same problem. To simplify, you must put all conductors associated with the same circuit in the same conduit.
How many bends in a conduit run would be required before the use of a pull box?
There has to be a pull box between every four quarter bends in a conduit run.
Does the Nec allow grounding electrode conductor to be run in conduit that has other conductors in the conduit and what code section?
No, the bare copper grounding conductor can not be in a conduit with other conductors. It can be in conduit by itself to provide mechanical protection for the wire.
Can a three phase circuit be installed in the same conduit or in different conduits?
The conductors of any three phase circuit must be run in the same conduit. If the circuit requires a neutral, it must also run with the conductors in the same conduit. (If they were to be run in more than one conduit or raceway, the circuit would not operate properly.)
Can you run 110 and 220 volt circuits in the same conduit?
Yes, 120 and 240 volts can be run in the same conduit.
Can you run parallel 4 ought aluminum conductors in the same 4 inch conduit?
Yes. Actually they should be run in the same conduit. You don't ever want to run parallel separately.
Why do you run all three phases in the same conduit to feed a panel?
The three phases when summed together should be very near zero (since this is a balanced system). If you ran only two cables in one conduit, the summed total would be a nonzero value. This nonzero current flow will induce a current in any nearby metalic structure that parallels the phase wires for any significant distance (such as the conduit, and joints). This will result in lost power (due to the induced currents creating a back emf), and localized heating in the conduit and metalic joints. Keeping all three phases together minimizes this, since the (vector) sum total of the current flow is near zero.
What is conduit wiring?
Conduit wiring is synonymous to wires in a pipe.
Why 2 different phase wire are not supposed to pass through same conduit?
According to the wording ,2 different phase wires "can" run through the same conduit. Not only can they, but if they are part of the same circuit they must. And in cases where conductors are paralleled, meaning more than one conductor per phase as is common in commercial and industrial installations, you put one conductor of each phase and a neutral, if one exists, and a ground in each conduit. Not doing so, meaning to put all of one phase in one conduit, causes a voltage to be induced into the conduit and a tremendous amount of heat builds up. Even when using pvc or other non-metallic conduit, somewhere along the way you have something metallic and have the same problem. To simplify, you must put all conductors associated with the same circuit in the same conduit.
Can 480 volt electric be run in emt conduit?
Yes 480 volt electric wiring can be run in emt conduit.
Can you have only one current carrying conductor in a conduit?
You can have only one current carrying conductor in a conduit, but that conduit must have a slot to relieve the eddy currents that will be created by the transformer effect created by the conductor. It is better to run the neutral or opposite conductor along with the hot conductor together in the same conduit, or through the same penetration, so as to minimize this effect.
What are some examples of a tee joint in the electrical trade?
A tee joint in the electrical trade is a conduit fitting. It is used in conduit work where there needs to be a device connected into the main conduit run. An example of this is where a light switch needs to be installed into the conduit run. The main conduit run starts at the distribution panel and proceeds to a lighting fixture. On the way a switch is needed to operate the light fixture. In the main conduit run a tee fitting is installed so as to pick up the switch for the fixture. When the conduit system is complete the wire is then drawn in. The "hot" conductor is pulled to the tee fitting and then diverts to the switch box to pick up the switch and then back up the same conduit to the tee fitting and then on to the lighting fixture. Splices are not usually made in tee fittings.
Can you use existing PVC conduit run from basement to 8th floor for 120v circuits for chillers?
The simple answer to your question is yes. But there are limits to how many wires can be in any conduit, and the current carrying capacity of the conductors can be affected by distance, ambient temperature, and how many conductors are contained in the same conduit. Other things to consider are, Can you physically fit the wires in there? Would it be easier to run a new conduit? Do you have the manpower necessary to get the work done?
How many bends in a conduit run would be required before the use of a pull box?
There has to be a pull box between every four quarter bends in a conduit run.
Does the Nec allow grounding electrode conductor to be run in conduit that has other conductors in the conduit and what code section?
No, the bare copper grounding conductor can not be in a conduit with other conductors. It can be in conduit by itself to provide mechanical protection for the wire.
