0
It all depends on the voltage and wattage of the dryer: maybe you only need 30 amp breakers with 10/3 wire, or maybe you need thicker wire and bigger breakers?
The rating plate on the dryer should tell you want power it takes and, if you are going to do this job safely and correctly, you should first of all be able work out the current or amperage from an appliance's power and the voltage.
<><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Can you change a 50 amp receptacle to a 15 amp receptacle?
Yes as long as you change the 50 amp breaker to a 15 amp breaker. You will be hard pressed to get the 50 amp #6 wire under the terminals of the 15 amp receptacle.
It is safe to use 8-3 wire on a 50 amp breaker?
No, it is not safe to use a #8 conductor on a 50 amp breaker. A #8 conductor is only rated at 45 amps capacity. By connecting it to a 50 amp breaker, which would trip at 50 amps on an overload, would overload the conductor by an extra 5 amps. This would be a conflict against the electrical code.
Can 50 Amp breaker replace 45 Amp breaker?
Both a 45 amp and 50 amp breaker would require 6 AWG wire. So if you have 6 AWG wire and any devices like an outlet are rated at 50 amps or greater you are okay.
240v nema6-50r outlet wired with 6 gauge wire and 50 amp breaker you need to run a heater with a nema 6-30p can you simply put a 30 amp receptical in place of the 50 amp receptical?
Not legally because the rating of the 30 amp receptacle would have a 50 amp breaker ahead of it. If you reduced the feed breaker to 30 amps and still use the #6 wire, this would be within the electrical code rules.
What size wire for 75 feet of wire for a 30 amp 220 volt oven?
A 30 amp breaker run 75 feet would require you use AWG #10 wire. But, an oven normally pulls more that 30 amps and I would not use #10 wire on a 30 amp breaker for an oven. Normally any newer oven is wired with AWG #6 gauge wire on a 50 amp circuit breaker so the breaker will not trip during heavy use of the oven. Some older ovens could use a #8 wire on a 40 amp breaker.
Can you use a 60 amp breaker with a 50 amp overcurrent device?
A 50 amp breaker is an overcurent device.
Can I replace a 50 amp 240v dryer outlet with a std 15 amp 240 volt outlet?
Theoretically yes if you remove the two pole 50 amp breaker and replace it with a 2 pole 15 amp breaker. This has to be done because the new receptacle is only rated at 15 amps and can not be protected by a breaker any larger than 15 amps.Physically this is not going to happen due to the fact that you will not be able to connect the existing #6 conductor, which fed the 50 amp dryer receptacle, under the terminals of the new 2 pole 15 amp breaker.
What is type of breaker for 41 amp's?
50 amp breaker.
What gauge wire and amp breaker do you use on a stove dryer and hot water heater?
A stove is a two pole 50, and hot water heater i would recommend the same.
Can a 100 amp main have 2 50 amp breakers?
Yes.Additional InformationBreakers and fuses protect the wires to prevent fire. The 100 Amp breaker in the meter base (main) protects the wire from the meter base to the breaker panel. The 50 Amp breaker in the breaker panel protects the wire from the breaker panel to the outlet. Sometimes the 100 amp main breaker is located in the panel.If you are asking "Can you use two 50 amp breakers for the main breakers with a 100 amp service, then yes you can. The National Electrical Code allows you to use up to 6 breakers as the main overcurrent protection.
Does a double 50 amp breaker make a 100 amp?
No, a double pole 50 amp breaker protects a 240 volt supply at 50 amps. The number that is on the handle of the breaker is the amperage that the breaker will trip at if an overload occurs on the circuit.
Can you use 8 three wire for a 50 Amp breaker to an oven range?
No .
Is 10mm cable safe for 50a breaker?
10mm cable is overkill for a 50 amp breaker. You can definitely use it.
Can you operate a 30 amp dryer on a 50 amp receptacle?
Yes and no. You can't put a 30A outlet on a 50A breaker as it will be a fire hazard. You can put a 50A outlet on it safely. Then you can plug the 30A load into it, but this is unwise and can be dangerous if you don't put fuses in your pigtail adapter. The best solution: Go ahead and install your 30A outlet but replace the 50A breaker with a 30A breaker. This is the safest and cleanest solution.
Can you change a 50 amp receptacle to a 15 amp receptacle?
Yes as long as you change the 50 amp breaker to a 15 amp breaker. You will be hard pressed to get the 50 amp #6 wire under the terminals of the 15 amp receptacle.
It is safe to use 8-3 wire on a 50 amp breaker?
No, it is not safe to use a #8 conductor on a 50 amp breaker. A #8 conductor is only rated at 45 amps capacity. By connecting it to a 50 amp breaker, which would trip at 50 amps on an overload, would overload the conductor by an extra 5 amps. This would be a conflict against the electrical code.
Is there a adapter for a nema 14-30 plug and a nema 14-50 receptacle?
No there are no adapters made for these types of installations. The reason there are no adapters is to provide a factor of safety. To plug a 30 amp plug into a 50 amp receptacle could allow 50 amps to be applied to a 30 amp rated cord. The 50 amp receptacle is more than likely being fed by a 40 amp breaker. Just change the plug cord to match the ampacity of the breaker ahead of the 50 amp receptacle. Or change the 50 amp receptacle and 40 amp breaker to a 30 amp breaker and use your existing cord plug.
