0
If you have a 400 Amp service using 500 MCM What size grounding electrode conductor is required?
Wiki User
∙ 12y ago
#2
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What is the difference between a ground conductor and a ground electrode conductor?
# A ground electrode conductor is a conductor that originates at the neutral or equipment ground buses in the main service entrance panel board or separating derived system (e.g. isolation transformer) # A ground electrode is a item that is in contact with the earth (e.g. Building metal frame, underground continuous metallic water pipe etc...) # A ground conductor is a conductor that is used to keep an electrical system continuous. Ground conductors are required, by code, in all PVC conduit runs. Ground conductors are also used to keep all metallic components of the installation at the same zero potential to overcome mechanical connections that would not carry a fault current back to the supply distribution panel.
800 amp service using parallel sets of 500 cu what size grounding electrode conductor?
The size called for is one ought (0). There are addendum to this rule depending on where you live in the country. Check the addendum to this code rule in your area.
What should the clearance be from service entrance panel to grounding material?
grounding material is not a good word but as short as possible is a good answer the entrance panel must be connected to the best possible ground this is called the grounding electrode the grounding electrode conductor connects to the ground bar in the entrance panel if the panel has a a neutral the neutral bar can be bonded to the ground bar Grounding electrodes form best to worse well casing water pipe (NOT plastic) buried plates or wire grid or bonded reinforcing steel driven rod if you are talking about distances to the panel it should be centered about shoulder height doors need to have about 2' of clearance in all directions weather open or shut
Can a paralleled grounded conductor be a 2?
A conductor used for grounding of the main service should be a single wire. The code book has a table that states the size of ground wire for different service panel amperages.
What size service ground is needed for a 350 parallel service?
From the question it is hard to establish whether the service size is 350 amps or the service conductors are 350 MCM in parallel. If the service is 350 amps, the grounding conductor is #3 bare copper wire. Parallel 350 MCM conductors will allow for a 600 amp service. The grounding conductor for a 600 amp service is a #1 bare copper wire.
What size copper grounding electrode conductor is required for a service that has three sets of 600 kc mil copper conductors per phase?
The grounding conductor of a service distribution is sized by the ampacity of the service. By just stating the wire size, this does not give this information, as many variables enter into what wires are used depending on length, ambient temperature and insulation factor to name a few.
What size grounding conductor is needed for a 80 amp service?
For service sizes of 100 amps and less a #8 bare copper conductor is required.
How many ground rods are required for a 200amp service in Indianapolis?
According to the NEC, if the ground rod supplements another grounding electrode such as a metal water pipe, you are required 1. If the ground rod or rods is your only grounding electrode, you are required at least 2, at least 6 feet apart. Check with your local jurisdiction for local requirements.
Iec 60502 2xfgy 61kv xlpe can you use the armour as grounding conductor?
NO some armored cable has a ground some sealtite has copper in the helix wit the drain shield some liquite has no conduction at all all armor is a helix which is a coil and acts as insulation at hi frequency xlpe cross linked polyethylene is an insulator service cable is never used for grounding grounding electrode conductor grounding equipment conductor grounding conductor are all separate from service cables if a tall trucks hits an overhead cable you dont want to lose the ground in short NO
What is an grounding electrode conductor?
It is the conductor that is used in service distribution panels that bonds the distribution panel's neutral bus bar to the ground electrode (rod). This brings all of the distribution panel neutrals that are connected to the same supply system to the same potential, that being zero. Should a supply service neutral open this ground wire will maintain the systems integrity until repairs can be made.
What size is the grounding electrode of a 400 amp service 500CM?
In Canada the grounding electrode requirement is for two steel 5/8" x 10' copper clad rods spaced 10 feet apart.
What is the difference between a ground conductor and a ground electrode conductor?
# A ground electrode conductor is a conductor that originates at the neutral or equipment ground buses in the main service entrance panel board or separating derived system (e.g. isolation transformer) # A ground electrode is a item that is in contact with the earth (e.g. Building metal frame, underground continuous metallic water pipe etc...) # A ground conductor is a conductor that is used to keep an electrical system continuous. Ground conductors are required, by code, in all PVC conduit runs. Ground conductors are also used to keep all metallic components of the installation at the same zero potential to overcome mechanical connections that would not carry a fault current back to the supply distribution panel.
800 amp service using parallel sets of 500 cu what size grounding electrode conductor?
The size called for is one ought (0). There are addendum to this rule depending on where you live in the country. Check the addendum to this code rule in your area.
Does the grounding bar hook to meterbox or breaker box?
A grounding bar is most often located in the breaker panel. This is where all your grounding conductors are landed. If the panel is your primary service panel, neutrals and grounds can both be landed there. The NEC (US) requires that all service equipment be bonded together. This includes your meterbox. To most people bonding and grounding look alike but they serve different purposes. In most cases this bonding consists of a #6 AWG solid copper conductor connecting your service panel to your meterbox and also whatever you happen to be using as a grounding electrode, usually a water pipe and ground rod. Consult a competent electrician for what is required in your area. I was on a job once where the city inspector expected this bonding conductor to be run with the service conductors inside the same conduit, which is what I would expect. But the power company for the same job required it to be run outside the conduit which is acceptable practice. Both were right, but we had to do it one way for the inspection and another way before power was supplied.
For a parallel feed to a 1200 Amp service 3 phase what size is the grounding electrode to main service with 3 600 mcm parallel runs?
500 mcm
What should the clearance be from service entrance panel to grounding material?
grounding material is not a good word but as short as possible is a good answer the entrance panel must be connected to the best possible ground this is called the grounding electrode the grounding electrode conductor connects to the ground bar in the entrance panel if the panel has a a neutral the neutral bar can be bonded to the ground bar Grounding electrodes form best to worse well casing water pipe (NOT plastic) buried plates or wire grid or bonded reinforcing steel driven rod if you are talking about distances to the panel it should be centered about shoulder height doors need to have about 2' of clearance in all directions weather open or shut
Can a paralleled grounded conductor be a 2?
A conductor used for grounding of the main service should be a single wire. The code book has a table that states the size of ground wire for different service panel amperages.
