0
Possibly if the kitchen does not have an electric over and electric cook-top and no eclectic water heater in the bathroom. If they are electric have an electrician evaluate what is being powered in the kitchen and the bathroom to determine if a 50 amp sub-panel is large enough. I would for sure at least go with a 60 amp sub-panel.
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
What size breaker do you use for a 100 amp sub panel?
A 100-A sub-panel would be fed from a 100-A breaker.
What is the minimum service size for a 225amp residential service?
A 200 amp service panel with a 60 amp sub-panel.
Is it OK to have 250 A of breakers in a 100 A panel?
Yes. Many installations have breaker totals higher that the main breaker of the panel. It is worked on a percentage basis. Not all of the breakers will be on at the same time. In a home, on a 100 amp panel the average load is 50 - 60 amps. The 100 amp main breaker is protecting the 100 amp rated panel board. If the load current goes higher that the panel board is rated at, the main breaker will trip to protect the board.
How many amps can be put on a 125 amp service?
You should not load a 125 amp panel any more than 100 amps.
How many circuits allowed in a 150 amp panel?
Panels are different. You can get 150 amp panels with 20 to 30 breaker spaces. The limit is stated by the manufacturer on a label attached to the panel. Hopefully you an find the label, sometimes it is on the inside of the cover
How do you wire a garage sub panel box from a 100 amp breaker in the house main panel?
you propaly can't sub panel from 100 amp panel. Just not enough amperage to be worth while. i had to up grade t a 200 amp main first and then I was able to take a 60 sub panel from that.
What would happen if a 200 amp breaker is used in a 100 amp sub panel?
There are two things to think about here. First of all a 200 amp breaker will not physically fit into a 100 amp panel. This is so designed because the panel buss is not designed to conduct 200 amps before the current is cut off. A 100 amp rating on the panel is the maximum amount of current that the manufacturer states, that can be handled safely. Second if the 200 amp breaker is in the main panel then everything downstream from that breaker has to be rated for 200 amp conductivity. The wire size will have to be 3/0 from the breaker to the first over current device in the sub panel which will be the sub panel's main breaker. The sub panel can not be a load center but will have to be a combination panel. I doubt that the 100 amp sub panel's main breaker lugs would be large enough to connect the 3/0 cable.
Can you feed a 60 amp sub panel from another 60 amp sub panel?
Yes
What is the largest sub panel you can install off from a 60 amp main panel fed by 100 amp service?
If what you state in this question is accurate this is an illegal installation. A 100 amp service can not have any equipment connected to it less that that of the service size. The 60 amp main panel must be a 100 amp panel to be a legal installation.
Can you had a 20 amp breaker on your 70 amp sub-panel that has already 70 amp total on it that consist of one 50 and two 15 amp breakers and the panel has 4 available spaces out of 8?
SeeIf_a_100A_breaker_panel_has_five_15A_breakers_and_four_20A_breakers_could_this_overload_the_panel
What size breaker do you use for a 100 amp sub panel?
A 100-A sub-panel would be fed from a 100-A breaker.
Can you put a 50 amp beaker in a 60 amp panel?
I've never heard of a 50 amp b-e-a-k-e-r. You can put a 50 amp b-r- e-a-k-e-r in a 60 amp panel; but you can only have an additional 10 amp breaker along with it. You may need to consider adding another larger panel or a separate 50 amp breaker box.
How do you wire a 15 amp 120V breaker in a 240v 30 amp breaker panel?
Look to see if the 30 amp panel is fed with a two wire or a three wire. If it is a two wire then you are out of luck. If the panel is fed with a three wire then the panel should have the neutral terminated in the panel. It is this neutral that you need for 120 volt connections. You didn't state how many panel slots there are in the panel. If you are able install a 15 amp breaker into the panel and connect the wires going to the load. The black wire will go to the breaker and the white wire will go to the neutral bar in the panel.
What amp do you need for a hairdryer plug?
A standard 115 rated bathroom circuit is enough power. You are supposed to have a GFCI on the line, either attached to your blow dryuer plug or as a receptacle.
Can a 200 amp breaker be purchased that only occupies 2 slots in the panel - if so where?
No. You can not buy a 200 amp that only occupies 2 slots on the panel.
Does a bathroom require it's own dedicated 20 amp breaker?
Every bathroom should have its own dedicated 20 amp electrical service breaker. The electrical service breaker should have a surge protector in the case that something electrical falls into water.
Where is the amp on a 1991 Toyota MR2?
the factory amp on a 91 mr2 is in the rear kick panel behind the drivers seat above the hood latch behind that panel
