0
What can we conclude about a four cylinder engine that has a 100 mm bore and 100 mm stroke?
Wiki User
∙ 7y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What does stroke mean in car terms?
The distance a piston travels within the cylinder bore, from the very top to the very bottom. This limit is the stroke.
If a typical radial engine has a bore of 5.5 inches and a stroke of 5.5 inches what is the area and where is the piston displacement?
This is the formula. Area = .7854 x bore^2 A = .7854 x 30.25 (5.5^2) A= 23.75 sq.in Volume = Area x stroke 23.75 x 5.5 = 130.625 cubic inches. *This is just one piston. If engine was a nine cylinder then 130.625 x 9 = 1175.625*
What is the compression ratio for an engine if each cylinder has a maximum volume of 500 cubic centimeters and a minimum volume of 50 cubic centimeters?
Compression ratio is exclusive to each cylinder, though they will all have the same result if they are the same dimensionally ( and they always are) > Divide the total engine capacity by the number of cylinders, this gives the capacity or swept volume of each cylinder (bore * stroke) > So in a 2.0 (2000 cc) litre 4 cylinder engine, each cylinder has a 2000 / 4 = 500 cc swept volume (bore * stroke) > The combustion chamber is the volume remaining at top dead centre (TDC) > Compression ratio = volume at BDC (swept volume + volume at TDC) / volume at TDC
How many cubic inches is a 302 bored out 60 over?
The displacement of a 302ci Ford V8 bored 60-over is 310.71ci V v V To calculate cylinder volume you should know the bore and stroke sized of an engine. Say a 350ci Chevy V8 bored 60-over: Normal bore of a 350 is 4" in diameter, so 60-over would measure 4.060" diameter bore. Stroke of a 350 is 3.48". Equation for measuring internal displacement of an engine is: Bore Radius^2 * 3.14 (Pi) * Stroke * # of cylinders = Internal Displacement So using that formula, we would divide of the bore diameter in half to get the radius. Radius is 2.03". Then calculate 2.03 to the 2nd power (2.03*2.03) is 4.1209". Now multiply 4.1209" by Pi which is 3.14. That equals 12.939626". This represents the 2-dimensional surface area of the bore. Now multiply that by the length of the cylinder stroke, which on this engine is 3.48". That equals 45.02989848 cubic inches (cylinder volume). You can round off the numbers to make it more simple, that's fine. Now 45.02989848 is the volume of a single cylinder of that engine. We know the 350ci has 8 cylinders, so we would now multiply by 8 to get the final calculation. The answer is 360.24 cubic inches. I hope this explanation helps a little.
What is total volume of cylinder bore?
That can be calculated for individual cylinders by the formula :- Pi R (2) x length of piston stroke.
What is the effect of changing the engine cylinder bore diameter?
Enlarging the cylinder bore will increase cc's in a 2 stroke and ci's ina 4 stroke.....
When an engine has a cylinder bore that is larger than its stroke what is this called?
Oversquare
Each cylinder of a four-cylinder two-stroke engine has a bore of 5.4 cm and a stroke of 5.4 cm. How would a manufacturer list the displacement of this engine?
1000 cc
What is over square Engine?
I'm not a mechanic / technician but as far as I know that is where the engine cylinder bore is larger than the stroke
How do calculate cc of four cylinder engine?
If Measuring in mm, ( Bore x Bore x Stroke x .7854 ) / 1000 = cc's
What does bore x stroke mean?
Bore = the (internal) diameter of the cylnder hole in the engine block. Stroke = the distance the piston travels up (or down) the bore during its' cycle. If you multiply the bore dimension by the stroke dimension you will get the volumetric displacement of that cylinder. thus, Vd = (3.1416/4) (dia.) squared x Stroke
What is bore and stroke in a motorbike?
Bore is the diameter of the piston/cylinder, stroke is the distance the piston can travel between its highest position and its lowest position in the cylinder.
What is the Bore and Stroke of 350 Chevy Engine?
The Bore of a 350 cid engine is 4.00, the stroke is 3.48 inch..
What is the cylinder bore on a 327 small block?
4inch bore 3.25 stroke formula bore x bore times stroke times .7854= cid
How engine capacity is worked out 4 cylinder engine?
I assume you mean engine displacement? To calculate engine displacement, use this formula: Bore x bore x stroke x .7854 x number of cylinders.
What is the stock cylinder size on a Chevy sb 305?
The bore and stroke is---3.740 bore and 3.480 stroke. STOCK 305
What does it mean by define an engine by its Bore X stroke?
bore is the diameter of the piston and stroke is the length the piston moves in the cylinder.for example if bore x stroke is 1x3 then 1 is the diameter of the piston and 3 is the length of the cylinder.if bore is greater than stroke then it is a short stroke engine.
