answersLogoWhite

0


Best Answer

It is called bridging.

User Avatar

Wiki User

13y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: What is the diagonal braces between floor joist?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Math & Arithmetic

What is the angle of a fire cut of a floor joist?

30 degrees


What size micro lam beam is needed for a 16 foot span supporting a floor with 8 foot joist on either side of it?

That really cannot be answered without looking at the entire set of plans.


How to build a platform over a sharply sloped floor?

How much slope and how long of a run? For short distance, up to 12 feet, and 12 inches of drop, you cut a 2x12 at the right slope and use them for the floor joist. For longer runs or greater slope, Use 2x6 level and use 2x4 legs under them.


Building a stairwell what are dimensions?

that would depend upon the distance between floors. with a distance of approx. 9' it would be around 37" wide and 8' long. The floor to floor height is only 1/3 of the solution for figuring out the stairwell length. That, with the tread, will give you the angle of the staircase. The less slope of the stairs, the bigger the well size needs to be for headroom clearance at the bottom. The other thing that needs to be figured in is the thickness of the floor system. The taller the joists, the sooner you'll hit your head and so the stairwell will need to be longer. For instance, 7 3/4"riser, 10"tread and 2x10 joists the well size needs to be 118 1/2" from the stair nosing edge to the head joist. For 2x12 joists it's 121". You'll need to add a little to this depending on how you hang your stingers for the actual framing of the stairwell. Check out stairwell-lengths.com for a book on all stairwell lengths for every angle and joist size.


There is a 2 by 8 running the whole length of your celling and right where your new skylights are can you cut it and sister it to the roof?

No. You need to support it, cut it and use 2 x 2x8s to tie back into the two joists next to it on each end. Use double joist hangers. By code you would also have to double the joist (s) you installed the hangers on... That is not always possible.

Related questions

How do you insulate Rim band joist in the basement?

Usually with a piece of insulation fitted between the joist, top of the foundationand the floor.


Does a joist note giving size spacing and direction and shown on a floor plan pertain to the framing above or below?

A joist note on a first floor plan would refer to the Joist below that floor, a joist note on the third floor plan woud be for that floor.


How much of a gap is left between each end of the floor joist and the web of the rim joist to prevent squeaking?

No gap is intentionaly left. Your squeaking will be between the subfloor and joists.


How much weight can you put on a floor joist?

it depen on the size of the joist


What are the ends of the joist nailed too?

Floor joist or ceiling joist? Floor joist have a board on the end all the way along the side of the building called a rim joist. Like the cross bar on the top of a T. Ceiling joist are nailed down into the top plate of the wall and to the rafters where possible.


What is the purpose of a joist?

to support the sub floor.


What is a housing joint used for?

Joist possibly ? A joist is the boards under the floor and above the ceiling that span the room or building. What the floor or ceiling is attached to.


Where can you find a floor joist span table when using 2 x 6 tongue and groove?

Not sure what you mean? floor joist span table???


What does the word joist mean?

Joist = one of the parallel pieces of timber to which the boards of a ceiling or floor are fastened


What is the span for interior floor decking?

I don't understand your question completely, but I think what you are asking is how far apart support can be for a subfloor or floor decking. It will vary with the type of construction, but for residential housing it's almost always 16 inches between the floor joists. That would be measured from the center of the joist to the center of the next joist.


What is the angle of a fire cut of a floor joist?

30 degrees


Are the nails used by air framing hammers as strong enough for framing floor joist?

No,if the joist is merely butted.The joists must sit on a bearer type of situation or have joist-hanger connectors.