0
What else can I help you with?
What wire size needed for 150 feet run on 30 amp?
This is a voltage drop question. To answer this question a voltage must be stated.
Is number 10 wire good for a 20 amp circuit that is 250 feet?
Assuming you are working with 120v, you need #4 AWG copper conductors.
How is wire pulled into a conduit of 100 feet?
A 100 foot fish tape and wire lubrication will be needed to make this wire pull.
What size tech cable for 480 feet 100 amp?
This is a voltage drop to establish wire size question. For a correct answer to this question two values are needed. One value needed is the voltage and the other is whether it is three phase or a single phase installation.
What wire size is needed for 15 volt circuit?
The wire size depends on how much current it will conduct.
What size wire is required for 120v 5amp 250ft?
Use AWG #10 wire on a 20 amp breaker.
How many feet of wire to make a slinky?
The length of wire needed to make a slinky can vary depending on the size and number of coils. A standard slinky typically contains about 67 feet of wire.
What size wire do you need to feed a 5 amp load run 1500 feet from the main at 120v?
A #3 copper conductor will limit the voltage drop to 3% or less when supplying 5 amps for 1500 feet on a 120 volt system.
What wire size needed for 150 feet run on 30 amp?
This is a voltage drop question. To answer this question a voltage must be stated.
What do you have to know to install a 120v electrical line?
You know the old saying: "If you have to ask..."! If you're asking this question, you should probably be calling an electrician. The answer to your question depends upon what you are trying to power up. This will determine what size wire you will need and therefore, the size of the circuit needed.
Can you have a 120v circuit on a 30 amp breaker?
No, electrical code typically requires that circuits be protected by a breaker that matches the wire size. A 30 amp breaker is typically used for circuits with larger wire sizes. For a 120V circuit, a 20 amp breaker is more suitable with appropriate wire size.
What size wire needed with a 100 amp load 250 feet away?
To determine the wire size needed for a 100 amp load 250 feet away, you will need to consider the voltage and allow for voltage drop. For a 100 amp load at 120V over 250 feet, you would need a wire size of at least 1/0 AWG. It's recommended to consult with a licensed electrician to ensure proper wire size for your specific situation.
What size wire for trolling motor?
The size of wire needed for a trolling motor depends on the motor's maximum amperage draw and the length of the wire run. A general guideline for a 12V trolling motor is 6-gauge wire for runs up to 10 feet, 4-gauge wire for runs up to 20 feet, and 2-gauge wire for runs over 20 feet to minimize voltage drop and ensure proper performance. Be sure to consult the manufacturer's recommendations for your specific trolling motor.
Is number 10 wire good for a 20 amp circuit that is 250 feet?
Assuming you are working with 120v, you need #4 AWG copper conductors.
What size service underground wire for 60amp at60 feet?
# 6 copper wire.
How do you wire a 120v A base emter for 120v?
To wire a 120V A base emitter for 120V, you would typically connect the emitter to the ground, the base to the input voltage source (120V), and the collector to the load. Ensure you follow proper safety precautions and consult the specific datasheet for the A base emitter you are using for correct wiring instructions.
What size wire should I use for a 120v 30amp 150 foot long run?
A #4 copper or #3 aluminium conductor will limit the voltage drop to 3% or less when supplying 30 amps for 150 feet on a 120 volt system.
