answersLogoWhite

0

In electrical wire sizing, a 3.0 mm² wire is larger than a 2.0 mm² wire. The numbers refer to the cross-sectional area of the wire, with a higher number indicating a thicker wire that can carry more current. Thus, 3.0 mm² wire has a greater capacity and is typically used for higher power applications compared to 2.0 mm² wire.

User Avatar

AnswerBot

∙ 1y ago
User Avatar

What else can I help you with?

Related Questions

Can you have a 120v circuit on a 30 amp breaker?

No, electrical code typically requires that circuits be protected by a breaker that matches the wire size. A 30 amp breaker is typically used for circuits with larger wire sizes. For a 120V circuit, a 20 amp breaker is more suitable with appropriate wire size.


Can 2 lengths of 14 Ga romex be used to make a 30 A circuit?

No, electrical wires can only be run in parallel on wire sizes 1/0 and larger. To supply a load of 30 amps you will need #10 wire and a 30 amp breaker.


What type of 30 amp electrical wire should be used for this project?

For a 30 amp electrical project, it is recommended to use a 10-gauge wire.


What is the recommended gauge for a 30 amp wire in a residential electrical installation?

The recommended gauge for a 30 amp wire in a residential electrical installation is typically 10 AWG (American Wire Gauge).


Should 20 AWG be used for a 30-amperes wire?

No. A #20 wire does not have the physical circular mils for a load of 30 amps. The wire would burn the circuit open.


Can 30 amp breaker be put in number 12 wire?

No, the National Electrical Code book (US) limits the current on a #12 AWG to 20 amps.


How should I properly wire a 30 amp breaker for my electrical circuit?

To properly wire a 30 amp breaker for your electrical circuit, you should use the appropriate gauge wire (typically 10 gauge for a 30 amp circuit), connect the wire to the breaker terminal, and then run the wire to the outlet or device you are powering. Make sure to follow all local electrical codes and safety guidelines when performing this task.


What is the recommended gauge for a 30amp wire in a residential electrical circuit?

The recommended gauge for a 30 amp wire in a residential electrical circuit is typically 10 AWG (American Wire Gauge).


What size ground wire is need for a 30 amp circuit?

On a 30 amp circuit, you would use a #10 copper ground. The ground never has to be larger than the ungrounded conductors.


What is the smallest copper wire size permitted by the national electric code for a 20 amp single phase electrical circuit?

I think you mean either what is the correct size or minimum wire size needed when a branch circuit is protected by a 20 A breaker. The size is 12 American Wire gauge (AWG). 14 AWG is used for 15 A circuit and 10 AWG for a 30 A breaker. The lower the gauge the larger the cross-section of the wire.


Can 10-2 wire be used for an outlet?

Yes you can. The existing 30 amp breaker on the two conductor #10 wire will have to be changed out to a two pole 20 amp breaker. The reason for this change out is that the new 20 amp outlet is only rated at 20 amps maximum. If the 30 amp breaker were left feeding the 20 amp device, It would be unsafe as it is 10 amps higher that the manufacturer's specifications of maximum amperage handling capacity of a 20 amp device.If the 30 amp circuit is only 120 volts, the neutral will have to be lifted from the neutral bar of that circuit and that will be the second wire that will be connected to the new two pole 20 amp breaker. This action will give you 240 volts across the new 20 amp outlet.


How do I properly wire a 30 amp breaker in my electrical panel?

To properly wire a 30 amp breaker in your electrical panel, you need to first turn off the main power supply. Then, connect the hot wire to the breaker terminal, the neutral wire to the neutral bus bar, and the ground wire to the ground bus bar. Make sure to follow the manufacturer's instructions and local electrical codes for safety.