0
Is it safe to have two black wires two white wires and two ground wires on a single breaker?
Hopefully just the black wires are on the breaker. Two circuits on one breaker. Shouldn't be a problem. It would depend on how many outlets or lights were on the breaker in total. Even then, there is very little chance of something drawing current from every outlet at the same time.
The only thing is you can't put two wires under one breaker (by code). You would have to wire nut them with a pig-tail then just put the one wire under the breaker.
What else can I help you with?
What colour wire goes to the breaker using 12-2 wire?
For a typical 12-2 wire, the black wire is the "hot" wire that connects to the breaker, the white wire is the neutral wire that connects to the neutral bus bar, and the bare copper wire is the ground wire that connects to the ground bus bar in the circuit panel.
How can you plug in 120V appliances such as a TV and VCR to an old 240V air-conditioning outlet with one white one black and one grounding?
At the breaker box the black and white will be on a double-pole breaker (or maybe even two separate breakers). To convert to 110V attach the black to a single pole 15 amp breaker, the white to the neutral bus bar (like all the other whites in there) and the ground to the grounding bar (like the other grounds). Then replace the receptacle with a regular 15amp 110V.
Should the black wire be bonded to the ground?
It depends on the color coding standards for what country you are in. In the US, the answer is no. The Neutral (white wire) is grounded at the service entrance to the building. The black wire should have roughly the same voltage to the neutral and to the ground. Something to be aware of: If you are using a meter and checking for continuity between the black wire and ground, it may tell you that they have continuity if the breaker is on.
How do you wire a 220v connection into the main panel?
I assume you mean you are wiring a 220 volt circuit. You will install a 220 volt double pole breaker of the correct size for the circuit. An example would be for an electric dryer that requires a 30 amp double pole breaker wired with 10/3 wire. You connect the Red & Black wires to the breaker. One on each screw. You now connect the White wire to the neutral bus bar in the service panel. Then connect the bare copper ground wire to the ground bus bar in the service panel. At the dryer outlet connect the black & red to the hot screws, white to the neutral, and ground to ground. They will be labeled on the back of the outlet.
How can you wire a normal 120V outlet out of a double pole circuit breaker?
well, the easy answer is, black wire to one pole of the breaker, white wire to the neutral bus with all the other white wires, bare wire to the ground bus with all the other bare (or green) wires. BUT the breaker must be 20 amps or less for residential outlets and you much match the wire size to the breaker, #14 for 15 amp breaker, #12 for a 20 amp breaker AND if there is only going to be one outlet, if it is a 20 amp circuit, the outlet has to be rated for 20 amps. Yes, but why would you want to? It is unclear to anybody else what you are doing and therefore a hazard. Do it right. Use a single pole breaker designed for 110V.
Do you need a 20 amp single or double pole breaker for your washer?
Washing machines in the U.S. operate on 120 volts. That requires a single pole 20 amp breaker and wired with 12/2 w-ground wire. Black to the breaker, white to the neutral bus bar, and copper ground to the ground bus bar.
How do you wire a wire to a wire?
If you are connecting 120 volts, you connect the black wire to the breaker, white wire to the neutral bar, and ground wire to the ground bar. If you are connecting 240 volts connect the black & white wires to the breaker, & ground wire to the ground bar.
How do you connect wire to a breaker?
There is 220 volts between the two poles. If you are running 2 wires (black and white) + ground then you hook black to one pole and white to the other. Put red or black electric tape on each end of the white wire and wrap around wire for 3 inches or so next to the connection so the next person will be able to see that the wire is hot and not a neutral.
How do you wire a 15 amp breaker?
Ground wire connects to the ground bar, white wire connects to the neutral bar, and black wire connects to the breaker. Be sure and turn off main breaker before installing the wire or the breaker.
How do you install 220 receptacle with white black and bare wires?
Assuming the wires are the correct gauge for application and breaker you use black and white wires as hot. Put red electrical tape on each end of white wire and connect red and black to the breaker output and bare wire to ground lug in panel. At receptacle connect black and red to hot contacts and bare wire to ground lug.
What colour wire goes to the breaker using 12-2 wire?
For a typical 12-2 wire, the black wire is the "hot" wire that connects to the breaker, the white wire is the neutral wire that connects to the neutral bus bar, and the bare copper wire is the ground wire that connects to the ground bus bar in the circuit panel.
Can you only use white and black wires on a 2 pole breaker?
Typically the black wire is "hot", and the white wire is neutral. A 2 pole breaker is most commonly used for 240 V, and as such, you would typically use a 3 conductor wire, with black, red and white (+ ground). In a typical application, the black and red are used in the 2 pole breaker, and neutral is connected to the neutral bar in the breaker panel.
Why is the ground wire hot at all outlet boxes on a particular circuit?
Most likely the ground (green) wire is mistakenly connected to hot instead of the hot wire (black) at the breaker panel! Possibly you meant the neutral wire not the ground wire, in that case most likely the neutral (white) wire is mistakenly connected to hot instead of the hot wire (black) at the breaker panel! In either case check all three wires in the breaker panel for that circuit to make sure they are all correctly connected! Black is hot, White is neutral, Green (or uninsulated in some cases) is ground.
How do you wire a 4800 watt heater that's 240 volts?
This will pull 20 Amps continuous so you will need a 30 A breaker and 10 AWG wire. You would have Black, Red, White and Ground. The 240 V would be on the black and red connected to the output from a two pole 240 A breaker. White would be neutral and green or bare wire would be ground.
How do you properly wire a single light switch?
To properly wire a single light switch, you need to turn off the power, remove the old switch, connect the wires to the new switch (usually black to black, white to white, and ground to ground), and then secure the switch in place before turning the power back on.
What is the second function of circuit breaker?
The two functions a circuit breaker can do is protect the circuit from a high current short circuit and through its thermal trip it can protect the circuit from overload conditions. A circuit breaker will trip if too large a draw or current flow occurs across a thermal shunt inside, it can also have a ground fault circuit interrupter integrated internally in case of a difference in potential between neutral and ground resulting from voltage leakage from appliances or to protect against potential electrocutions A double circuit breaker provides access to the 2 legs of 120V in the back plane on the breaker panel. There are now typically 4 wires away from this breaker, a bare ground or earth ground, a white wire for neutral or bonded ground, a black wire for 1 leg of 120 and a red or blue wire for the 2nd leg of 120. You can use either leg and the white wire to access 120 or use the black and red/blue to access 240, white would then be used on the 3rd plug and ground goes to the ground lug or if missing it ties with the white and goes on the 3rd leg.
How do you wire a ge double pole 50 amp circuit breaker with black white and ground?
Answers for USA, Canada and countries using similar 60Hz mains supply.By stating that it is a double pole breaker it is presumed that the load device needs 240 volts to operate. Connect the black wire to one pole of the breaker. Apply black electricians tape to the white wire to identify it as a current carrying conductor. This wire is then terminated into the second pole of the breaker. The ground wire is terminated on the terminal ground strip in the back of the breaker panel. On the load end also identify the white wire with black tape before connecting it to the load. What this signifies to any one with electrical knowledge is that the white wire is not a neutral but carries load current.If you do any such work yourself, always turn off the power at the breaker box/fuse panel BEFORE you attempt to do any work AND always use a meter or voltage indicatorto insure the circuit is, in fact, de-energized.IF YOU NOT ALREADY SURE YOU CAN DO SOME ELECTRICAL WORKSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
