0
A minimum of 15-amp breaker is "needed", but a 20-amp is often required by electrical code for that situation.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What size breaker does it take to run a outdoor well?
Normally AWG #10 wire on a 30 amp breaker but it really depends on the size of the pump. The pump manufacture will specify the size wire and size breaker needed.
What size of breaker to use on a wall unit 220 heater?
The size of the breaker needed for a 220V wall heater depends on the current rating of the heater. Generally, for a 220V heater, a 20-amp breaker is common. However, it's important to check the manufacturer's specifications and local electrical codes for the appropriate breaker size.
A range name plate says 78 amps what size breaker needed?
To determine the size of the breaker needed for a 78 amp range, you typically need to use a breaker that is the next size up from the amp rating. This means that you would need an 80 amp breaker to safely accommodate the 78 amp range. However, always consult with a qualified electrician to ensure the correct breaker size for your specific electrical setup.
What size breaker is needed for a 220 v hot water heater?
A 220V hot water heater typically requires a double-pole breaker rated at 20-30 amps, depending on the specific power requirements of the water heater. Make sure to consult the manufacturer's specifications or a qualified electrician to determine the appropriate breaker size for your specific unit.
Is 60 amp breaker good for 225 stick welder?
The 225 amps is the secondary output amperage. Look on the machines nameplate to find the input amperage. It is that amperage that is needed to size the feed wire and there the breaker size. When you find that amperage you may want to re question the breaker size.
What size breaker would e needed for 10.8 amps?
In standard construction this would require a 15 amp breaker and 14 gauge copper wire.
What size breaker is needed to connect 5500 watt gas powered generator?
A 5500 watt gas powered generator typically requires a 30 amp breaker for a 240 volt connection. It is recommended to consult the manufacturer's specifications to ensure the correct breaker size for your specific generator model.
What size wire is needed to operate a three quarter horsepower opener 250 ft from the breaker?
Wire size is calculated from the amount of current the load draws. More information is needed. Voltage and amperage will do fine.
When your toaster and microwave are both running your 20 amp breaker trips Can you replace the 20 amp with a 30 amp breaker?
Definitely not, the 20 A circuit breaker is there to protect the wiring from becoming overheated. Any more current is potentially dangerous. The total power and current taken by the toaster and microwave should be checked to make sure that the 20 amp breaker is tripping correctly. It could be faulty. Both items should have a plate on the back, near where the power cord goes in, giving details. If the toaster and microwave together genuinely draw more than 20 amps you need a 30 amp circuit installed with the right wire size and a 30 amp breaker.
What size breaker is needed for 208 volts 6 amps using Ohm's law?
20 amp In North America code states a two pole 15 amp breaker will do the job.
When installing a circuit breaker do you size the breaker to correct wire size or the device its controlling?
When installing a circuit breaker, you size the breaker based on the wire size. The breaker should be matched to the ampacity of the wire to ensure proper protection against overloads and short circuits. The device being controlled by the breaker is not a determining factor in sizing the breaker.
What size circuit breaker for a 1 ton air conditioner unit?
For a 1 ton air conditioner unit, the circuit breaker size typically ranges from 15 to 20 amps. The exact size needed will depend on the specific model and requirements of the air conditioner, so it is best to consult the manufacturer's specifications or an electrician to determine the appropriate circuit breaker size for your unit.
