0
What else can I help you with?
What size of a circuit breaker for a 400v 64 amps?
To select a circuit breaker for a 400V system with a load of 64 amps, you typically choose a breaker rated for at least 125% of the continuous load. Therefore, the minimum rating would be 64 amps x 1.25 = 80 amps. A circuit breaker rated at 80 amps would be appropriate, ensuring it can safely handle the load without tripping under normal conditions. Additionally, consider the type of load and application, as well as any relevant local electrical codes.
What size breaker should be used for a 3.6 kW oven?
3000 / 240 = Amps. You de-rate a breaker by 20 % for continuous load like an oven. You could get by with a 20 Amp breaker and 12 AWG wire. However, I would recommend 30 Amps and 10 AWG for an oven for the long run.
Should 25 amps breaker be replaced by 20 amps?
For typical residential house wiring 12 AWG wire is required for a 20 Amp breaker. If you change out the breaker for a 25 A breaker you would have to rewire the circuit with 10 AWG. In that case you could up the breaker to 30 Amps. All outlets and switches should be rated at the same voltage and current as the breaker.
What size circut breaker for 10-2 wire?
A #10 wire has the capacity for 30 amps. No breaker larger than 30 amps should be used to protect the circuit.
What size breaker should you use for a unit that draws 75 amps?
Depending upon what type of "unit", you would want at least an 85-amp breaker, and the next standard size would be 90 amps. You might use an 80, depending upon the duty cycle of the unit, but the 90 will be required for constant use.
What is the appropriate size of a breaker needed for a 240-volt circuit that requires a 50 amp breaker?
For a 240-volt circuit that requires a 50 amp breaker, the appropriate size of the breaker needed is 50 amps.
A range name plate says 78 amps what size breaker needed?
To determine the size of the breaker needed for a 78 amp range, you typically need to use a breaker that is the next size up from the amp rating. This means that you would need an 80 amp breaker to safely accommodate the 78 amp range. However, always consult with a qualified electrician to ensure the correct breaker size for your specific electrical setup.
What is type of breaker for 41 amp's?
For a 41 amp load, you would typically use a 50 amp circuit breaker. The general rule is to select a breaker size that is 125% of the continuous load amps or equal to the load amps if it is not a continuous load. In this case, 41 amps is considered a continuous load, so you would round up to the nearest available breaker size, which is 50 amps.
What is the appropriate breaker size for a washer?
The appropriate breaker size for a washer is typically 15-20 amps.
What size breaker is needed for a 240 volt 34 amp hot tub?
Add 25% so it comes to 42 amps
What size breaker is needed for a 115V 60HZ motor?
Its been a while since ive brushed up on my electricity knowledge, but im fairly certain that breaker capacities are based on amps. I think you would have to know the amperage of the motor before you were able to conclude what size you need.
What size wire and breaker do you need for a 5000 watt garage heater?
Look on the heater and see what amps it is pulling. That will determine the wire size and breaker size. It must be on a dedicated circuit. 15 amps = AWG # 14 wire with 15 amp breaker 20 amps = AWG # 12 wire with 20 amp breaker 30 amps = AWG # 10 wire with 30 amp breaker 40 amps = AWG # 8 wire with 40 amp breaker
What size breaker should you use for a unit that draws 58 running amps?
To determine the correct size breaker, you need to ensure that it is rated higher than the running amps of the unit. For a unit drawing 58 running amps, a breaker that is rated for at least 70 amps would be appropriate to provide a safety margin and prevent tripping due to overload.
What is the standard to select circuit breaker?
Add up your amps to calculate your breaker size. Add up your loads (amps), divide by 0.8, and choose that size breaker. If that number does not correspond to a standard size breaker you go to the next higher standard size breaker.
What is the recommended breaker size for a hot tub?
The recommended breaker size for a hot tub is typically 50 amps.
If an electrician have a circuit that pulls a load of 10 amps what size breaker must that circuit be protected by?
For a circuit with a load of 10 amps, a breaker of 15 amps should be used for adequate protection. It is important to choose a breaker size that is slightly higher than the load to prevent frequent tripping and ensure safety.
Is 60 amp breaker good for 225 stick welder?
The 225 amps is the secondary output amperage. Look on the machines nameplate to find the input amperage. It is that amperage that is needed to size the feed wire and there the breaker size. When you find that amperage you may want to re question the breaker size.
