To determine the volume of dirt in this scenario, you would multiply the area (3 acres) by the depth (200 feet). First, convert acres to square feet (1 acre = 43,560 square feet). Then, multiply the area (3 acres = 130,680 square feet) by the depth (200 feet) to find the total volume of dirt.
The depth of dirt can vary greatly depending on location and other factors. In general, topsoil can range from a few inches to several feet deep before reaching the subsoil or bedrock below. Factors such as climate, vegetation, and geological history can influence the depth of dirt in a particular area.
You are exerting a pulling force known as tension to remove the rock from the dirt.
There is no dirt in the hole because a hole, by definition, is an empty space.
CONVERSION CHART1 Cubic yard 1 inch deep will cover 324 Square feet1 Cubic yard 2 inch deep will cover 162 Square feet1 Cubic yard 3 inch deep will cover 108 Square feet1 Cubic yard 4 inch deep will cover 81 Square feet1 Cubic yard 5 inch deep will cover 64 Square feet1 Cubic yard 6 inch deep will cover 54 Square feet(Length in Feet)( Width in Feet)*(Depth in Feet)=cubic feetExample: Say you have an area that is 12' x 18 '. You want to cover it with 6" of material.Multiply, 12' x 18' x *.5' to get 108 cubic feet. You see, 6" is .5 feet or 1/2 a foot.Now, devide 108 cubic feet by 27 cubic feet(1 yard) to get your total yardage at 4 yards.If you want a 3" cover you use 1/4' or .25'. A four inch cover is 1/3 foot or .33', etc.OR ---- Multiply your square footage by .003 for 1" coverage.0061 for a 2" coverage .0092 for a 3" coverage and.0123 for a 4" coverage. It takes 12.3 cubic yards of top soil to cover 1,000 square feet at 4". Hope this helps. ----
There is no dirt in a hole, as a hole is an empty space where dirt has been removed.
There is no dirt in the hole, but if you want to know how much dirt was removed to create the hole, then:3 acres is an amount of area (you don't have 'square acres'). You could express this volume as acre-feet, but this term is usually used when referring to flooding (an acre of land flooded with 1 foot of water, for example). 1 acre = 43560 square feet, so 3 acres = 130680 square feet.(130680 square feet)*(200 feet) = 26136000 cubic feet {26.136 million cubic feet} In the dirt industry, the standard measurement is cubic yards {often referred to as just 'yards' of dirt}. There are 27 cubic feet in a cubic yard, so this is equivalent to 968000 cubic yards.
You are mixing volume (square yard) and area (length x width). How deep do you want the dirt? One foot deep you need about 80 square yards of dirt.
All of it
None. If it is a hole that means there is absolutely nothing inside the hole meaning that there is no dirt at all in a hole even if it was dug up from dirt. No matter how big the hole, the result is the same.
None, if it is a hole.
I'm assuming you mean one meter deep with a one square meter footprint. The answer is 1*1*1=1m^3 = one cubic meter. Actually, that is how much dirt was taken out to make the hole. There should be no dirt in the hole, otherwise it wouldn't be a hole.
You need to tell us how DEEP.
600lb.
6 cubic square
6 cubic yards of dirt will cover 70 sq ft ... 2 ft 3 3/4 inches deep
16 sq ft*0.5 ft = 8 cubic feet.
Without knowing the width of the shovel, it's not possible to calculate the volume of the hole. But whatever its volume is, there's no dirt at all in the hole.