0
I have a 30 amp circuit 10 ga wire in an island. I've been told that I need a 40 amp breaker on 8 ga wire which will require breaking through my slab . Are there any 30 amp cooktops?
Wiki User
∙ 11y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Does a dryer need a quick disconnect breaker?
A dryer does not require a quick disconnect breaker. However, it is recommended to have a dedicated circuit with a proper circuit breaker for the dryer to ensure safe operation and to meet building code requirements.
What is a circuit breaker with 2 switches?
A circuit breaker with 2 switches typically refers to a double-pole circuit breaker. This type of circuit breaker has two separate switches that simultaneously disconnect both the positive and negative wires of a circuit, providing complete electrical isolation. It is commonly used for appliances or devices that require a dedicated electrical connection.
What size in amperage circuit breaker should be used for a pool pump?
The size of the circuit breaker for a pool pump should be determined by the pump's current draw. The breaker should be sized to accommodate the pump's full load amperage with a 125% safety margin. Most pool pumps typically require a 15 or 20 amp circuit breaker.
What size amp circuit breaker should be used for a home entertainment system?
A typical home entertainment system may require a 15-amp circuit breaker. It's important to ensure the total power consumption of all components does not exceed the amp rating to prevent overloading the circuit. It's recommended to consult an electrician for proper sizing and installation.
What size circuit breaker to use on well pump?
To determine the correct size circuit breaker for a well pump, you should check the manufacturer's recommendations on the pump's label or in the manual. Typically, most well pumps require a 15-amp or 20-amp circuit breaker for residential use. Make sure the breaker is appropriately sized for the pump's power requirements to avoid damage or safety hazards.
Cause of a circuit breaking tripping?
Tripping is caused by excessive current, which is usually the result of a fault in cable or equipment. The circuit breaker is there for safety and it trips to prevent a possible fire starting.
What size amp circuit breaker would protect a 12kW boiler?
The breaker protects the wiring not the boiler. 12,000 watts at 240 volts will require 50 amps. So, you will need a 60 amp breaker using AWG# 6 wire on a dedicated circuit.
Why two different 30 amp cooktops wont work on a double pole 30 amp breaker using 10 4 wire One 4 wire cooktop only has fan working other 3 wire cooktop does not work at all?
So many variables not presented here. 1) Was it wired by a journeyman electrician? 2) IS the name plate rating as to voltage correct for the circuit supplying it? 3) Is it used or new equipment? Try to give as much info as possible? Once you get them working, one 30 amp 2 pole breaker will not adequately supply two 30 amp cooktops. The breaker will trip. If you intend to operate both at the same time, they need to be on separate 30 amp circuits or one 60 amp circuit which would require larger wire
What size in amperage circuit breaker should be used for a pool pump?
The size of the circuit breaker for a pool pump should be determined by the pump's current draw. The breaker should be sized to accommodate the pump's full load amperage with a 125% safety margin. Most pool pumps typically require a 15 or 20 amp circuit breaker.
What the breaker size require for kW?
The use of a breaker in a circuit is to protect the wire size used in the circuit from becoming overloaded. Using the wattage of the load does not help for breaker sizing because the breaker operates on amperage. Amperage can be found from wattage by using the following equation. I = W /E. Amps = Watts / Volts. As you can see the amperage can not be calculated because there is no voltage stated.
What size circuit breaker to use on well pump?
To determine the correct size circuit breaker for a well pump, you should check the manufacturer's recommendations on the pump's label or in the manual. Typically, most well pumps require a 15-amp or 20-amp circuit breaker for residential use. Make sure the breaker is appropriately sized for the pump's power requirements to avoid damage or safety hazards.
Does a residential condo require a main breaker in each unit?
No, a residential condo does not require a main breaker in each unit. Typically, the main breaker is located in the electrical room or utility room of the building, and it controls the power supply to all the units. Each unit may have individual circuit breakers, but a main breaker is not required in each unit.
What are the difference between cooktops and rangetops?
Cooktops and rangetops differ in features and styles. Cooktops are available in gas version or electric version and require specific counter cutout for installation whereas rangetops are only available in gas version and must be installed into both the countertop and cabinet.
What is the problem if the breaker isn't tripped and there is no power to my switch in computer room switch in foyer switch for outside porch and alarm panel is dead?
The most likely problem is that the breaker has tripped. On some breakers there is a indication window that shows a red flag if the breaker needs resetting. On other breakers there is no indication but a slight misalignment of the breaker handle as compared to the other ones. On the distribution panel find the breaker number of the circuit that is off from the panel index. Push the breaker handle to the furthest off position that you can. As the handle is moved to the off position you will feel a bit of resistance. Push past it as that is the breaker resetting. Return the breaker to the on position to see if the circuit has re-energized. The only other reason is that a wire has become disconnected in the circuit. If you have been doing any electrical work on the circuit start looking in that area. To troubleshoot these types of problems it will require the use of a volt meter to check to see if the circuit is "hot" from the breaker out. Then it is just a matter of finding where the voltage stops and locate the problem.
Can you run 14 gauge wire off 12 gauge 20 amp breaker?
You could if it fit properly in the connector, but it would be massive overkill since you only need 12 AWG wire. You also have to make sure the load can physically accommodate that larger size wire. Every so often someone will replace an electric cooktop witha gas one. All of the new gas cooktops require a 110v outlet. The old electric cooktop may have been run with a 50 amp breaker (and probably 6 gauge wire) In order to convert this 220 v circuit to a 110v circuit we change to a 20amp breaker. Depending upon the brand of breaker sometimes the wire will fit into it. If not, we splice on a short piece of 12 gauge wire and then connect to the breaker.
Will multiple tripping of a circuit breaker damage the circuit breaker?
You don't specify whether you mean low-voltage circuit breakers, such as MCBs (miniature circuit breakers) or high-voltage circuit breakers. In either case, repeated tripping under fault conditions causes arcing which damages the main contacts of the circuit breakers. For this reason, high-voltage circuit breakers are taken out of service after a specified number of tripping operations, so that the contacts can be maintained or, if necessary, replaced. MCB contacts are inaccessible, and the MCB may eventually require replacing.
Why two trip coil require in breaker?
Having two trip coils in a circuit breaker provides redundancy and increased reliability. If one coil fails, the other can still operate the breaker. Additionally, using two trip coils may allow for greater flexibility in the control and operation of the breaker.
